Which is the best way to get and the best tape?

Post Reply
shalom
Posts: 772
Joined: Wed May 04, 2011 10:54 am
My Location: DF
Location: PR

Which is the best way to get and the best tape?

Post by shalom » Thu Jul 19, 2012 7:02 am

I'm using blue tape and I am working out. sticks much with the heat.which is the best way to get it, part-time or after full time process.

User avatar
duke46
Posts: 11030
Joined: Thu Jun 03, 2010 8:32 pm
My Location: East Coast NC
Location: New Bern NC
Contact:

Re: Which is the best way to get and the best tape?

Post by duke46 » Thu Jul 19, 2012 7:59 am

I guess you are using the Blue tape like made by 3M? If so then you just want to leave it in the oven long enough for the powder to set so its not powder any more and then pull the part and remove the tape and then finish the cure of your part.

If you want to tape something up and leave the tape on it for full cure then you need to buy the proper tape for that

http://powder365.com/store/index.php?ma ... cPath=5_25
All I have said is said just for meanness so I don't have to argue with anyone!

http://www.pcitdad.com

shalom
Posts: 772
Joined: Wed May 04, 2011 10:54 am
My Location: DF
Location: PR

Re: Which is the best way to get and the best tape?

Post by shalom » Thu Jul 19, 2012 11:17 am

Its commonly blue used for powder i Buy in CC

User avatar
duke46
Posts: 11030
Joined: Thu Jun 03, 2010 8:32 pm
My Location: East Coast NC
Location: New Bern NC
Contact:

Re: Which is the best way to get and the best tape?

Post by duke46 » Thu Jul 19, 2012 12:49 pm

shalom wrote:Its commonly blue used for powder i Buy in CC



That tape should not cause any problem unless you are going way over the temp of your powder and the tape? I have used green/orange/ a blue from EW and a glass one and never had that problem???? The only other problem maybe if two toning something would be the powder it is place over was not fully cured?

I am lost on what else to tell you.
All I have said is said just for meanness so I don't have to argue with anyone!

http://www.pcitdad.com

shalom
Posts: 772
Joined: Wed May 04, 2011 10:54 am
My Location: DF
Location: PR

Re: Which is the best way to get and the best tape?

Post by shalom » Thu Jul 19, 2012 2:36 pm

Ayyyyyyyyy its true i used uver 430 fo RO primer :D

User avatar
duke46
Posts: 11030
Joined: Thu Jun 03, 2010 8:32 pm
My Location: East Coast NC
Location: New Bern NC
Contact:

Re: Which is the best way to get and the best tape?

Post by duke46 » Thu Jul 19, 2012 5:37 pm

shalom wrote:Ayyyyyyyyy its true i used uver 430 fo RO primer :D



Well as per normal CC does not list the max temp on their tape but 430 should not have had any problem with it? I guess you used a IR gun for that 430 temp and not just the temp of your oven? If so your oven might be off some. But most tapes will handle 500 I think?
All I have said is said just for meanness so I don't have to argue with anyone!

http://www.pcitdad.com

User avatar
SCOTTRODS
Posts: 5949
Joined: Thu Jun 03, 2010 1:43 pm
My Location:
Location: Garland, Texas

Re: Which is the best way to get and the best tape?

Post by SCOTTRODS » Thu Jul 19, 2012 6:15 pm

Probably the same stuff..... Eastwood has the blue High Temp tape as well..... That's where I get mine (I buy it on eBay for a small discount).

Post Reply